Filet de stabilisation pour zones de circulation vertes TENAX TR

lawn reinforcement net

Data sheet

chiodi a U per il fissaggio

Accessoires
30 cm U Staples

TENAX TR

Filet de stabilisation pour zones de circulation vertes (herbe)
TENAX TR est une grille en polyéthylène haute densité, très résistante.
Une fois installé, il fournit une surface très stable, convient parfaitement pour résister à la charge des voitures et camions de faible tonnage.

TENAX TR évite la formation d’ornières due à la circulation des voitures et garantit une bonne prise pour les racines d’herbe.

AVANTAGES
	Quand le gazon a poussé à travers le filet, celui-ci devient invisible
	Facile à installer
	N’écorche pas, ne coupe pas
	Facile à installer
	Peut être utilisé même sur des surfaces déjà verte
	Recyclable
	Excellent impact esthétique

APPLICATIONS
	Application temporaires comme le parking lors de rencontres sportives
	Concerts ou salons
	Assemblement de roulottes et de caravanes
	Aires de jeux de plein air

lawn reinforcement net

dimensions (m)	maille mm	couleur	code-barres EAN	rouleaux/ palette	unité de vente
2.00x30	30x27	green	8002929010810	8	roll

INSTALLATION

INSTALLING ON GREEN SURFACES
1) Trim the grass. 2) If necessary, level the laying surface level any excessive undulations with sandy subsoil (a mixture of cultivation soil and sand), sowing in areas that have been filled in. 3) Unroll TENAX TR. Strips of product at the requested length can be cut with a safety knife or secateurs. For this purpose, support guides or paper moulds (for obtaining special shapes) can be used.		4) Fix one end of the roll and its sides at intervals of 2 m with TENAX “U” pins (30 cm in length) or similar, being careful to overlap adjacent reels (fig. A). The net must also be fixed in areas where its height from the surface is deemed excessive; fixing must be carried so as the net has tension when installed in order to avoid the formation of creases and to ensure adequate adherence to the laying surface. 5) For obtaining the best results we suggest that vehicles do not use the reinforced grass until it has grown to at least 35 mm. Alternatively, the grass can be sown by simply laying the TENAX FVP before installing the net.
INSTALLATION ON SURFACES TO BE SOWN
1) When converting pre-existing areas, we recommend excavating the area to a minimum of 3 cm, if the foundation has sufficient draining properties. If the presence of clayey soil, an adequate draining system must be installed to avoid rain water from stagnating. 2) Carefully level the laying surface. 3) Spread the sandy subsoil (a mixture of cultivation soil and sand) suitable for grass with a thickness of 3 cm at least. 4) Carry out sowing. We recommend the use of a Gramineae mixture suitable to be trodden on.	5) Unroll TENAX TR. Strips of product at the requested length can be cut with a safety knife or secateurs. For this purpose, support guides or paper moulds (for obtaining special shapes) can be used. 6) Fix one end of the roll and its sides at intervals of 2 m with TENAX “U” pins (30 cm in length) or similar, being careful to overlap adjacent reels (fig. A). The net must also be fixed in areas where its distance from the surface is deemed excessive; fixing must be carried so as the net has tension when installed in order to avoid the formation of creases and to ensure adequate adherence to the laying surface.	7) Cover the net with sandy soil, filling any remaining hollows. The net must be entirely covered and the layer of soil must be minimal in order to allow the re-growth of roots around the net’s mesh. 8) Carry out sowing, roll and dampen with the same frequency and methods as used with normal grass. 9) For obtaining the best results we suggest that vehicles do not use the reinforced grass until it has grown to at least 35 mm and has been cut twice.